Aliphatic Urethane Concrete Sealer
Aliphatic Urethane Concrete SealerNot sure of the color? Pick the Sample Jar - 4 oz to test it at home before the full order.
Couldn't load pickup availability
Not sure which to pick?
Not sure which to pick?
Tell us about your project and the year your home was built, and we'll suggest a good place to start. Ask us here.
Premium urethane toughness. Water-based ease.
Aliphatic Urethane Concrete Sealer gives concrete a hard, long-wearing, clear medium-gloss finish that is tougher than water-based acrylics. It is single-component and water-based: no mixing, no special equipment, and tools clean up with water.
- Built to wear. Superior abrasion and solvent resistance, and a hard, long-wearing surface at full cure.
- Shrugs off spills and stains. Excellent resistance to water, alkali, acids and stains.
- Made for sun and weather. Excellent UV resistance, and its vapor permeability allows it to be used outdoors.
- Clear finish that shows the concrete. Goes on milky, dries clear in less than an hour, and leaves a medium gloss that darkens the surface slightly.
- Easy to apply. Roll it on with a 1/4" short-nap roller or use a pump-up sprayer. Low VOC (under 100 g/L), quick to dry and fast to recoat.
- One sealer, many jobs. Use it alone on bare concrete, overlays and micro toppings, or as a finish coat over epoxy for added wearability. Indoors, outdoors, floors and vertical surfaces.
Where to use it
Basements, foyers, warehouses, stores, restaurant floors, kennels, concrete countertops and brick hearths, or almost any surface that needs an abrasion-resistant, low-mil coating. On vertical surfaces, its properties against graffiti make it a good coating.
How to apply
- Prep. The surface must be sound, clean, dry and free of oil, grease and other bond inhibitors. Profile to at least a 200-grit level, or until it readily absorbs water. Neutralize any acid etch. Moisture content must be 30% or less on an electronic moisture meter.
- Check conditions. Follow the Product Data Sheet for application conditions. Don't apply if rain is expected within 48 hours or humidity is above 80%.
- Apply thin. This is a 2 mil coating. Use a 1/4" short-nap roller (microfiber or woven) or a pump-up sprayer, and keep rolling it out for an even finish. Never use a foam roller: it puts air into the material and causes bubbles.
- Recoat. Wait at least 1 hour, or until tack-free. Two or three light coats give the best results.
A bluish haze can appear on some surfaces while it cures. That is normal.
Coverage and dry times
| Coverage | About 250 sq ft per gallon |
| Dry / recoat | 1–2 hours / 1–3 hours |
| Foot traffic | 4–6 hours |
| Light to moderate traffic | 24 hours |
| Wheel traffic | 24–48 hours |
| Heavy traffic | 72 hours |
| Full cure | 7 days |
Specs
| Chemistry | Single-component, water-based aliphatic urethane |
| Finish | Clear, medium gloss |
| Solids | 25% |
| VOC | Under 100 g/L |
| Film thickness | 2 mil |
| Cleanup | Water |
| Removal | Chemical stripper or mechanical means |
| Sizes | Gallon and 4 oz Sample Jar |
Typical values, not a specification.
Good to know
- May be slippery once cured. Take caution.
- Keep it from freezing, including in storage.
- Apply a test area on the actual surface first.
- For professional use. Read the label and SDS before use.
FAQ
Can I use it on a garage or basement floor?
Yes. It takes wheel traffic after 24–48 hours and resists water, alkali, acids and stains. Remove all oil and grease, and check the slab with a moisture meter first (30% or less). Work with good ventilation.
Can I put it over epoxy?
Yes. It is designed as a finish coat over epoxy or similar coatings for increased wearability.
Why does it look milky?
That is normal. It goes down white and turns clear in less than an hour, depending on conditions.
Will it change the look of my concrete?
It dries clear with a medium gloss and darkens the surface slightly. Do a test area first.
How does it ship?
By UPS from Olathe, Kansas, typically within 1–2 business days.
Is there a tinted version?
Yes. Concrete Stain & Seal uses the same water-based urethane base, tinted for one-step color and seal.
Documents
Share

Let customers speak for us
from 207 reviewsHave not started project, yet. But I'm confident it will be fine 🙂
My handyman was able to patch a section of mortar on my limestone. It was quick and easy from ordering to delivery to results.
The stain worked perfectly.
We are using this mortar for our stone wall restoration project, and so far we are very happy with the results. The mortar is easy to work with, and the color blends nicely with the existing stonework. Good quality product!
After visiting the shop and talking to the team i got the right mortar to repoint my stone foundation and brick work with powered dyes. The softer and natural tone compared to using bigbox type N grey mortar product keeps the integrity of my 110yr home without looking like a bad diy patch job.
Came out beautiful and better than I had hoped
Shipped quickly. Arrived quickly. It mixed easily and adhered to my spalling bricks. So far so good.
The perfect mortar for 126 year old bricks (granite boulder and brick foundation built in 1900). Very happy with the mortar and clear instructions. Thank you ProMason!
Worked perfectly. Stain changed color of existing brick to the tone I was expecting giving it new life and blends with other new finishes.
I haven't had a chance to mix and use the mortar yet. However, the customer service is great. They immediately sent a replacement package of colorant since the original had leaked.
Our project turned out wonderful! What an amazing difference. It completely changed the look of the house!!
Easier to apply than I anticipated.
My first time staining brick and I was nervous on how it might turn out because I was going from dark brown tone bricks to gray tone (before and after photo submitted)Blended my own color combo and It looks amazing.
The stain covers well and a quart did a good amount of surface area. The perfect shade was achieved by mixing 2 colors. It looks great and is a nice brick border update!
The masonry sealer worked great. It was easy to apply and dried perfectly.
So far, so good. It will take time.