Lime Wall Plaster - Color Skim 128 Kashan

This Color

Kashan is a luminous, sun-soaked neutral that captures the golden warmth of desert architecture and ancient, sun-baked brickwork. Named after the historic Iranian city celebrated for its masterful masonry and clay-tiled courtyards, this shade is a sophisticated, "gilded" earth tone. It sits between a pale ochre and a toasted cream, mimicking the specific glow of a limestone facade at the height of the golden hour.

A Mineral Alternative to Painting

Replace paint with this non-sanded smooth lime plaster. Designed as a skim-coat color finish, it creates a stunning decorative mineral surface on interior walls. This finish can be applied over both primed drywall and plaster walls.

Coverage and Surfaces:

Coverage: 50-75 SF per-gallon

Application: Venetian Plaster Trowel

Surfaces: Interior Walls

Primer / Surface Preparation: Pro Mason Plaster Primer-Smooth (on drywall & non mineral surfaces)

Sealer: Lime Plaster Sealer Gloss/Low Gloss

Visual Depth & Movement

This plaster is colored with integral coloration using the liquid B part provided with the kit. These pigments highlight the visual movement created by the application strokes and the minerals within the finish.

Composition & Surface Compatibility

Color Skim Wall Plaster creates a breathable and beautifully smooth finish with visual depth and is applied as a paper-thin skim coating. The finish and composition is similar to smooth Veneziano and venetian plaster with no sand within the lime and fine crushed marble plaster. It can be applied to most smooth-finished, stable interior wall surfaces such as drywall and concrete board after being primed as well as plaster walls as a final color finish.

Customizable Sheen: Matte or Burnished

This finish can be burnished to increase sheen or be applied as a matte finish with no burnishing action, which is an easier process for DIY projects. Rewetting the surface to work to a smoother finish prior to initial setting is possible to create a highly refined finish.

Application Thickness & Preparation

Color Skim Wall Plaster is intended as a final color finish to be applied to smooth surfaces that have been primed with Pro Mason Plaster Primer Smooth or to a dampened mineral plaster substrate. This plaster should not be applied thicker than 1/16” in a single application and should not be used to build surfaces or fill gaps.

Easy Mixing & Extended Working Time

Add Part A and B together and mix to a workable paste. Mixing with a mechanical drill mixer designed for paint or plaster is advisable to create a smooth, lump-free mixture. This hydraulic lime plaster has a slow set time relative to gypsum plaster skim coat finishes. This can be helpful for those who are new to plaster work and reduces urgency to work quickly. This plaster is formulated to retain water during drying and does not require misting or damp curing in normal conditions.

Application Instructions: Pro Mason Color Skim Wall Plaster on Drywall

1. Surface Preparation Prepare the drywall to a smooth surface (Level 4 finish or higher is ideal). Fill holes and complete all mudding and taping before proceeding.

2. Priming Apply one even coat of Pro Mason Plaster Primer Smooth using a paint roller. Allow to dry fully.

3. First Coat Apply the first coat of plaster at 1/16” or thinner. Do not attempt to achieve full coverage or build up the surface; this is a decorative color finish and will crack if applied too thickly. It is better to apply multiple thin layers than one thick layer.

4. Smoothing Once the first coat is dry, lightly sand with fine sandpaper or knock down high points with a plaster knife to ensure smoothness.

5. Second Coat Apply the second coat. If conditions are warm, you may mist the surface immediately before application to extend working time. Note: Do not mist finished work unless you plan to re-trowel that area.

6. Third Coat & Burnishing If needed, apply a third coat once the second is dry. After the final coat is fully dry, you may burnish the surface to increase sheen and depth.

7. Curing & Sealing

• Water-Based Sealers: Allow the plaster to cure for 1–3 weeks before applying. Use water-based sealers only. Longer curing times are ideal if the project timeline allows.
• Wax, Soap, or Oil Finishes: Allow a minimum of 48 hours (1 week recommended) before applying.

Temperature: Air and surface temperatures must be maintained between 55°F (13°C) and 85°F (29°C).

Humidity: Ideal relative humidity (RH) is 50%–75%.